The portable welding fume extraction and smog exhauster can be
equiped for one and two arms for the unfixed working positions.
Pulsing back-flushing automatic dust-removal system.
The welding fume extraction is easy of installation, and has no
technical requirements when the customer install and use it. The
flexible extraction arm is made from high quality material of PVC
and steel wire, which is anti-corrosion, heat-resistant of up to
140°C. It can swivel 360º and can be brought in any desired
direction without additional support. It is equipped with the
damper to adjust the wind. It is equipped with the caster wheels
and can be freely mobile to meet the requirements of different work
places.
The purified gas can meet the standard requirements and can enter
into work room or indoor place, which is helpful to keep the room
close, maintain the temperature and be convenient for work.
Operating Principle:
Under the help of the fan device, the welding fume is sucked into
inlet through multi-direction sucking hood. There is the flame
arrester in the inlet, so the spark can be blocked here, and the
left fume and dust is sucked into gravity separator. The bigger
paticiles firstly descend into dust bag. The smaller particles is
arrested in the surface of core filter. The cleaner gas then flow
into clean room after being purified by core filter. In clean room,
the clean gas is then further purified by active carbon. At last,
the gas meets the required standards and enter into air or other
required room.
Facility Characteristics
1) It is equipped with ABB turbo fan and motor imported from
Germany and America, with overload prevention circle to avoid motor
damage. It is of steady performance.
2) It is equipped with built-in centralized PLC controlling system.
The operation panel is clear and simple, very easy to operate.
3) Pulsing back-flushing automatic dust-removal system: The filter
core is the automatic rotating and back-flushing type, which keeps
the filter core surface clean when working, to insure the stable
blowing rate; The air compressor parts are connected with high
pressure rubber pipe with high pressure air-inflow in the bottom,
which insure the facility always in good working condition.
4) The filter core is imported from the large company in America
with long useful life. It can arrest the 0.3μm particles. The
filtering effect is good for all kinds of particles including the
wet particles.
5) It is equipped with the all-directions sucking arm of 360 degree
rotating. It can suck the fume exactly from the source which make
best of the fume collection efficiency, and insure the workers’
health in the largest extent.
6) It is equipped with three layer filter system to avoid the
damage effect of flame and large slag particles, which extend the
useful life, more safe and more reliable.
7) The clean air is exhausted uniformly and diffusely through the
gridiron outlet, so it can minimize the noise.
8) It is attached with all-direction caster wheels, which makes the
facility movable freely and easy to position.
9) Photoelectric controlled on/off, energy saving and high
efficiency. The hood has the lighting device which is upon
customer’s choice.
10) The parts working condition are all stable and has long useful
life, meantime easy to be replaced.
LB-JZ Series Welding Fume Purifier Parameters Table:
| Model | Airflow (M3/h) | Voltage (V) | Power (kw) | Size L xWxH (mm) | Noise (dB) | N. W. (KG) |
| LB-JZ 1500 | 1500 | 380 | 1.5 | 650x550x1250 | ≤60 | 75 |
| LB-JZ 2400 | 2400 | 380 | 2.2 | 650x550x1250 | ≤68 | 80 |
| LB-JZ 3600 | 3600 | 380 | 3.0 | 650x550x1250 | ≤72 | 105 |
| LB-2400S | 2400 | 380 | 2.2 | 650 x550x1250 | ≤69 | 98 |
| LB-3600S | 3600 | 380 | 3.0 | 650 x550x1250 | ≤72 | 120 |
LB-JZ (D) back-flushing pressure is 0.5-0.6Mpa.
Custom design and production is available.
Other main FUME EXTRACTOR products:
1. LB-JZX model(double cartridge filters):
2.LB-BG model(wall mounted type):
3.LB-JK model(with simple structure):
4.LB-JF model(High vacuum pressure type):
Videoes:
The work video about the welding fume extractors for the welding
condition, which have a good performance :
http://loobo.cn/video/gyhb/600.htm
https://youtu.be/yLBAvptRM-M
http://loobo.cn/video/gyhb/606.htm
The company development film :
http://loobo.cn/video/693.htm
We,Qingdao Loobo Environmental Protection Technology Co.,Ltd is
aimed to air purifying and kinds of removing fume exhausted, with
its own R&D team more than ten years manufacturer, located in
Qingdao city of china, specialized in the main products:
1,portable welding fume extractors,and soldering fume extractors
etc.,
2.downdraft benches(grinding dust removal worktable),
3.central fume purification projects,
4.Spare parts:flexible suction arm,etc.
All of our products with the ISO9001, and CE certification for
parts of products, the quality can be guaranteed.
ATTN: Miss Molly Huang
Tel: 86-15064847869
Skype: mollyhice
Email: hqhpl@126.com
